nema gearbox

Ever-Power Corporation , announces its right angle NEMA gearbox made to IP65 specifications for use in clean down applications in packaging equipment and comparable machinery. Rated backlash can be 30 arc-minutes with options for 4 or 8 arc-minutes. The NEMA 34 flanged gearbox has 440C Stainless bearings with seals and Nitrile o-bands shaft seals on both input and result. All fasteners are stainless. Hard anodized aluminium or 316 Stainless housings can be found. Customizing for other than NEMA motors or your specific application is very easily done.
This Nema 17 stepper motor with 39mm body and 1.68A rated current, integrated with a 41mm Planetary gearbox of 5:1 equipment ratio. It’s a good solution to applications that with unique space but need low rate and/or high torque.
Electrical Specification
Manufacturer Part Number: 17HS15-1684S-HG5
Motor Type: Bipolar Stepper
Step Angle: 0.36 deg
Holding Torque without Gearbox: 39Ncm(55oz.in)
Rated Current/phase: 1.68A
Phase Resistance: 1.6ohms
Voltage: 2.7V
Inductance: 3.2mH ± 20%(1KHz)
Gearbox Specifications
Gearbox Type: Planetary
Gear Ratio: 5 : 1
Efficiency: 95%
Backlash at No-load: <=15 arcmin
Max. Permissible Torque: 3.5Nm(495.6oz.in)
Moment Permissible Torque: 6Nm(849.7oz.in)
Max. Radial Load: 150N
Ambient Temperature: -10 – 90℃
Insulation Class: B
Noise: <=50 dB
Life: 20000 h
Physical Specifications
Body Size: 42 x 42mm
Motor Length: 39mm
Gearbox Length: 41mm
Shaft Diameter: Φ8mm
Shaft Length: 23.5mm
Key-way Length: 14mm
Number of Leads: 4
Lead Length: 320mm
Weight: 680g
Replaced by the 3325_0, a engine with the same NEMA size and same torque.
This NEMA-17 motor comes with an integrated Planetary gearbox with a 52/11 :1 ratio. It generates 16.2 Kg-cm of torque at 1.68 Amps.
When linked to a 1067 – EP, the 3317 includes a maximum speed of just a little over 900 RPM. At the output of the gearbox, the step angle is a little under 0.35°. When using the step angle in calculations, you should derive the precise step angle by dividing 1.8° by the gearbox reduction ratio.
This particular revision of the 3317 is made by a different manufacturer, but should behave very much like the revision 0 version.
Brother Gearmotors NEMA C-Face Speed Reducers
The gears in these NEMA C-Face speed reducers are high strength, maintenance free and may be mounted in virtually any direction with their slip fit “O” ring design. Low to high reduction ratios, flange attach or foot install types, right position or hollow shaft correct angle types available. Suit NEMA C-Encounter AC motors, brushless DC motors and brushed DC motors.
For 1/2 HP up to 3 HP Motors
NEMA C-Face, 140TC and 180TC input flanges
Inline Helical Gear Acceleration Reducers
Right-Angle Hypoid Gear Speed Reducers
Product Lineup
Product Features
Allowable Torque
Downloads & Reference
NEMA C-Face Velocity Reducers Lineup
Output Power
Gear Type
Input Power
Gear Ratios
Maximum Input Speed
NEMA 56C Speed Reducers
NEMA C-Face Speed Reducers
Parallel Shaft (Foot Attach)
1/2 HP
1 HP
2 HP
3 HP
5:1 ~ 200:1 3600 r/min
Parallel Shaft (Flange Attach)
Right-Angle Hollow Shaft
5:1 ~ 240:1
Right-Angle Solid Shaft
5:1 ~ 240:1
*Torque and Swiftness vary based on insight voltage and frequency, please review item specifications for details.
Longer Life
In comparison to a spur gear of approximately the same pitch diameter, Helical gears can transfer high loads in greater speeds. That is due to the gradual engagement of one’s teeth and simple transfer of the load.
Helical Gears
Lightweight and Compact
Die cast aluminum gear housings make these acceleration reducers light in weight, allowing engineers to create less expensive mounting provisions
Maintenance Free
High-quality synthetic grease is utilized in every gearboxes. They are packed at the factory and do not need maintenance filling or level checks. This saves valuable time at create and eliminates concern for expensive oil disposal needed by the EPA.
Mount in Any Direction
These gearboxes are sealed with machine “slip” match “O” rings and dual lip springtime shaft seals on both the motor and input shaft and result shaft driver. Therefore, the gear motors can be mounted in any conceivable direction without concern for the positioning of a breather connect.
NEMA Output Flange Planetary Gearboxes, Max. Ratio 1000:1
Spec

Gearing Arrangement:Planetary,Spur
Frame Size:42.6/60/90/115/145 mm
Ratio:3~1000:1
Nominal Output Torque:8~215 N.m
Nominal Input Speed:2500~4000 rpm
Max. Input Speed:5000~6000 rpm
Backlash:12~15 arcmin, three stages, 6~9 arcmin, single stage, 8~12 arcmin, two stages
Noise Level:60~67 dBA/1m
Enclosure:IP65
Lubrication:Synthetic Lubricant
Key Features

The Ever-Power EP Series gearboxes are equipped with a NEMA output flange with metric shaft, to provide exceptional torque ratings and convenience of many of present servo and stepper movement control applications. The gearboxes are drop-ins for most industry standards and obtainable from one to three stages with ratios 3:1 up to 1000:1, the best backlash of < 6 arc-moments. Adapters for all servo and stepper motors. Features:
5 frame sizes with NEMA 17, 23, 34, 42, 56 flange and metric shaft
Backlash only 6 arc-minutes
Ratios up to 1000:1
High radial and axial loading capacity
20,000 hours service life
Synthetic grease, free of maintenance
Reliable operating performance, cost effective integration

Tags:

China Coupling Co., Ltd.

Mail: [email protected]

As one of leading Couplings manufacturers, suppliers and exporters of mechanical products, We offer Coupling and many other products.
Please contact us for details.

Recent Posts